When waking from suspend, only enable the LED drivers if they were not previously set to disabled by the user. This functionality was removed by the recent updates to adapt Massdrop keyboards to QMK RGB Matrix. Affects Massdrop CTRL and ALT keyboards compiled using Massdrop Configurator mode.
Microsecond (us) delays are now handled by a busy wait loop according to MCU frequency. This replaces the system counter method which had an overhead of around 12us.
TC5 device and supporting routines removed as it was the old us delay counter.
wait_ms is now properly a macro to CLK_delay_ms.
wait_us is now properly a macro to CLK_delay_us.
Removed CLK_get_us as it has no use.
All calls to CLK_get_ms() have been replaced by timer_read64() with corrected typing.
All calls to CLK_delay_ms() have been replaced by wait_ms().
All calls to CLK_delay_us() have been replaced by wait_us() and timings verified or updated as needed after review on scope.
Corrected typing of variables using 64bit ms timer readings if needed.
MCU Pins for debugging, LED, boot tracing, and shift registers are now configurable at keyboard level.
Macros led_* replaced by DBG_LED_*
Macros m15_* replaced by DBG_1_*
Macros m27_* replaced by DBG_2_*
Macros m28_* replaced by DBG_3_*
For CTRL and ALT keyboards, debug boot tracing pin default now set to pad M27 instead of M28 since although M28 is not being used, it is technically a signal for USB port detection.
m15_print(...) renamed to dbg_print(...) to get away from hard coded port names.
dbg_print function now follows similar pattern to debug led output.
Rewrote USB state tracking for implementation of suspend state.
Updated suspend.c in entirety.
Main subtasks (generally hardware related) are now run prior to keyboard task.
Added hid_listen USB device for arm_atsam USB protocol.
Debug printing is now done through the console device (CONSOLE_ENABLE = yes) rather than the virtser device, for viewing in hid_listen.
Function dpf(...) renamed to CDC_printf(...) and should now be called directly if intending to print to the virtual serial device.
* Update for SEND_STRING usage
Update for SEND_STRING usage.
Sending keyboard reports (kbd, nkro) now obey the minimum polling time.
While attempting to send a keyboard report and waiting for a USB poll, other functions of the keyboard, including LED effects and power management, will continue to operate at their intended intervals.
* Updates for send string, syscalls, stdio, debug prints, auto shift
Now properly waiting for previous keys sent over USB to complete before sending new.
Added heap to linker and now compiling with syscalls support.
Removed custom string functions and now using stdio.
dprintf now works as intended through virtser device.
* CTRL and ALT keymap updates
CTRL mac keymap updated
ALT default and mac keymap updated
ALT rules.mk added Auto Shift with default no
* Code cleanup as per discussion with vomindoraan
Code cleanup as per discussion with vomindoraan
* ALT keymap update
Added additional End key on layer 1 to match key cap
* LED driver update addressing PR #3871
Update sync between IS31FL3733 drivers is causing varying behavior in keyboards including brightness mismatch and slight flicker at very low rgb values. Visually, disabling sync is not noticeable. Ref PR #3871 by guarnacciaa.
* CTRL LED scan code mapping fix
Fixed scan codes to properly align with key wiring
* Update scan codes for caps and scroll lock lighting
Update scan codes for caps and scroll lock lighting according to previous scan code mapping update
Added support to enter bootloader from software (bootloader version must be newer than "v2.18Jun 22 2018 17:28:08" until workaround for older is created).
Updated CTRL and ALT keymaps for entering bootloader with Fn+b held for >500ms.
Added basic MacOS keymap for ALT.
USB sleep LED indicator now turns off after 1 second.
Slowed down debug LED code printing.
Renamed keyboard alt67 to alt and adjusted necessary files where alt67 appeared.
CTRL keymap fixed enum structure name.
usb2422 removed stray define no longer used.
* Massdrop keyboards readme update
Massdrop keyboards readme update for flashing instructions
* ctrl and alt keyboard readme update
Updating make command in Massdrop CTRL and ALT keyboard readme files to reflect directory change
* Massdrop SAMD51
Massdrop SAMD51 keyboards initial project upload
* Removing relocated files
Removing files that were relocated and not deleted from previous location
* LED queue fix and cleaning
Cleaned some white space or comments.
Fix for LED I2C command queue.
Cleaned up interrupts.
Added debug function for printing numbers to scope through m15 line.
* Factory programmed serial usage
Ability to use factory programmed serial in hub and keyboard usb descriptors
* USB serial number and bugfix
Added support for factory programmed serial and usage.
Incorporated bootloader's conditional compiling to align project closer.
Fixed issue when USB device attempted to send before enabled.
General white space and comment cleanup.
* Project cleanup
Cleaned up project in terms of white space, commented code, and unecessary files.
NKRO keyboard is now using correct setreport although KBD was fine to use.
Fixed broken linkage to __xprintf for serial debug statements.
* Fix for extra keys
Fixed possible USB hang on extra keys report set missing
* I2C cleanup
I2C cleanup and file renames necessary for master branch merge
* Boot tracing and clocks cleanup
Added optional boot debug trace mode through debug LED codes.
General clock code cleanup.
* Relocate ARM/Atmel headers
Moved ARM/Atmel header folder from drivers to lib and made necessary makefile changes.
* Pull request changes
Pull request changes
* Keymap and compile flag fix
Keymap fix for momentary layer.
Potential compile flag fix for Travis CI failure.
* va_list include fix
Fix for va_list compile failure
* Include file case fixes
Fixes for include files with incorrect case
* ctrl and alt67 keyboard readme
Added ctrl and alt67 keyboard readme files
patrickmtandDrashna Jaelre
